The Battery and The Charging System
The ebb and flow of electricity has an air of mystery often to the layman. So, before I identify the peculiarities of some of the automobile charging systems in favor at the period our Wolseleys were produced, I shall endeavor to explain this ebb and flow mentioned.

There are two main factors concerning the passage of electrical energy along a wire cable, flow and pressure. The former being the speed of the current measured in amps and the pressure is the volume or amount measured involts. A simple analogy is water flowing through a pipe. The size of the pipe generally governs the volume of the flow whilst the pressure it is being pumped at effects the speed at which it travels through the pipe. (If water is pumped through a very small pipe at high pressure we have the basic principle of our modern day "water blaster" used in exterior cleaning i.e. small amount of water at very high speed, the force of which does the cleaning.) When we do the same thing with electricity, we then introduce a third factor called resistance (measured in ohms) and all metal has this resistance to the flow of electricity.


Copper has a low resistance factor and so is mostly used in manufacture of auto wiring cables. Resistance is very important to keep in mind when considering auto charging systems. Old batteries develop a high resistance to accepting charge because the plates have "hardened" with age. Loose connections along the cable joint create resistance, dirty battery terminals connections also. Keep them SCRUPULOUSLY CLEAN AND TIGHT AT ALL TIMES. Make certain the battery earthing lead connection to the chassis/frame is tightened onto clean metal, no paint or dirty grease to create resistance.

Check all connections for signs of excessive heat after using the starter motor 2 - 3 minutes with ignition dead.Hot spots indicate resistance at that point, severely restricting the flow of current. Sometimes, cables are too small to carry the flow (amps) required and so get warm - if this happens to the main battery/starter leads,perhaps heavier cables will make a world of difference tostarter motor performance which means quicker and easier engine starts.

Copyright Wolseley Car Club
This site designed by G.McCutcheon 2009

In the car charging system it is necessary to have an
"interrupter" commonly called a "Cut-out" to prevent
battery current flowing back from the battery and
earthing out through the generator earth brushes and
discharging the battery when the engine stops. When the
engine fires up rotation of the generator provides
current to energize a magnetic coil in the cut-out
pulling _a set contacts together completing the circuit to
the battery. Upon becoming stationary these spring
loaded contacts automatically open and prevent drain
back,. In early model cars this was the only unit fitted
in the charging system. Make sure these contacts arc not
burnt and pitted to cause resistance - use a fine point;.
file or carborundum paper to clean them up - be sure to
disconnect the battery first.


During the late 30's and early 40's the first of the compensated voltage control units came into use this the "black box" usually mounted under the bonnet on the fire- wall. Lucas MCR1. MCR2, RF95, 95/3, 96, 97, RO106/1. 106/2, RB187 and RB108. Remove the cover to expose 2 "bobbins", one is the cut-out, the second is the voltage control unit which also has a set of contacts which become pitted and burnt with use and create resistance (our old enemy) and reduces the amount of charge to the battery.

The function of the voltage unit is to regulate the generator charge rate according to the state of charge of the battery. To maintain a 6 volt battery at full charge, the regulator is set at the factory at 8 - 8.5 volts. For a 12 volt battery the regulator setting is 16 - 16.5 volts. Cleaning and polishing the contacts is necessary after considerable use of the vehicle and the voltage setting will need to be checked with a 0.30 volt meter on open circuit. (Place a piece of card between the cut-out points) If the reading is below that mentioned earlier I suggest you take it to your auto electrician to have it adjusted.

Later cars were fitted with "3 bobbin" regulators identified as RB31@ and the later RB34@. Of the 3 bobbins 1 is the "Cut-out", 1 is the "Voltage regulator" and the 3rd is a "current regulator". These units are quite complicated and should only be serviced by a competent repairer, who are becoming difficult to find as the younger artisans do not have the knowledge or correct information.

For general guidance as to whether your regulator needs overhaul, take notice of the ammeter reading after having used some battery current operating the starter motor with the headlights on. The charge rate should go up to approximately 20 amps for at least 10 - 15 minutes before cutting back. If the rate drops after 3 minutes or less, chances are it needs points cleaning and amp andvolt settings adjusted. If you fit a good battery which is fully charged to your vehicle and after 3 - 4 weeks using the car, the battery has lost charge (using the hydrometers) and is down to half charge or less is a sure indicator the regulator is tired and needs overhaul.


Remember- Keep your battery fully charged AT ALL TIMES
And so double or even treble the life of what is a
Reasonably expencive item, plus always knowing your
engine will start on the coldest mornings.

             Mort Andrews
By Mort Andrews
RF95/3 Off 1934 Wolseley Hornet
with cover on
RF95/3 Off 1934 Wolseley Hornet
Inside front veiw
RF95/3 Off 1934 Wolseley Hornet
inside top
RB106/2 Off 1953 Wolseley 6/80
cover on
RB106/2 Off 1953 Wolseley 6/80
cover off
RB106/2 Off 1953 Wolseley 6/80
cover off side view